• Sew Retro

Free pattern and Tutorial for the NANCY Kimono


The Nancy is a free pattern and tutorial for your own use at home and not to be reproduced commercially. The super simple Nancy Kimono is a simple pattern hack from the Clara Kimono

Beginners project.

Materials and Equipment

170cm cm of fabric I got mine from here

50cm of light weight iron on interfacing.

Matching thread, pins, tape measure, chalk and scissors.

Suitable Fabric.

It is important that you choose the correct fabric for The Nancy.

Your Fabric choice needs to be medium to light weight, to achieve the look in the image,

Heavy or stiff fabric would result in a different look to the images shown.

The Nancy would be very suitable for lightweight fabric such as viscose, polyester or a lightweight crepe.

Tips for beginners

Seam allowance 1 cm this is the distance between the edge of the fabric and the stitch line. You will find a series of parallel lines engraved on the needle plate of your sewing machine pick the one marked with the measurement you need and keep the edge of the fabric to this guide

RS = right side of fabric WS = wrong side of fabric.

Press = Iron the section you had just sewn, seam should be ironed open.

Sizing

Small

Fits up to size 12 - the finished garment measures, front laying flat 58 cm and the back 58cm total finish circumference 116cm

Medium

Fits size 12 to 14 - the finish garments measures front laying flat 62 cm and the back 62 cm total finish circumference 124cm

Large

Fits size 16 to 18 - the finish garments measures front laying flat measures 66cm and the back 66cm, total finish circumference 132cm

  1. Make a paper pattern for the Clara kimono follow the measurements for your size as given above,

  2. OR Pin the selvedge edges of you fabric together, and using tailors chalk, measure and chalk out the pattern pieces.

  3. Cut out the kimono

  4. Using your iron on interfacing cut out 2 pieces measuring 84cm x 8cm.

  5. Check your measurements and cut out.

  6. Lay both of the front pieces RS up with the short measurement at the top, measure from C to A (all sizes) 12cm. Cut a small notch or mark with chalk, measure from C to B 40cm (all sizes), drawn a chalk line from A to B, repeat on the other side as shown in the diagram, THE FRONTS MUST BE A PAIR. Cut, A to B, repeat on the remaining side.

  1. Join the front shoulder seam to the back shoulder seam using a French seam. With WS together pin, the front shoulder to the back shoulder and stitch a 0.5cm seam, press flat, flip your work over, leaving the RS together stitch again using a 0.5cm seam. Press. Repeat on the remaining shoulder.

  1. Iron on the interfacing to the WS of the band x 2.

  1. Join the short seams on the neck band together giving you one long band, fold the band in half RS together, and press your band should measure 4cm x 168cm cm, using a 1cm seam stitch together the ends of the band.

  1. Clip the corners and turn inside out, press.

  2. Fold the back neck of the jacket in half and mark with a pin. Fold the band in half and mark with a pin. Join the jacket and the band together at the point marked by the pins.

  1. Continue to pin the band to the jacket. N.B. the band ends 2cm from the hem. Stitch the band to the jacket, start sewing from the middle of the back neck stitching down to the hem of the band, the shoulder seams will need to be pushed forward and pined flat to the front of the jacket.

  2. Zig zag or over lock this seam. Press.

  1. Fold the sleeve in half and mark the middle with chalk or a pin. Lay the kimono flat RS facing up and pin the sleeve to the jacket. The chalk mark or pin must match at the shoulder seam. Repeat with the remaining sleeve. Stitch using a 1 cm seam allowance. Repeat on the remaining sleeve. Zig zag or over lock the seams.

  1. With the RS together fold the sleeve in half and pin, making sure the shoulder seams are pushed towards the sleeve. Pin the under arm seam as shown.

  1. Stitch the sleeve and side seam together. Start sewing from the raw edge of the sleeve, stitching over the seam you made to join the shoulder to the jacket. Stop, leave your needle in the fabric, lift up the foot, and swivel the jacket around until you are able to sew the side seam. Repeat on the remaining side. Over lock or zig zag the seams.

  1. Making the cuff. With RS together fold the cuff in half and stitch the short seams together, press the seam flat. Fold the cuff in half RS together and press as shown in the image.

  2. Attach the cuff to the sleeve. With the RS of the sleeve facing, slip the cuff onto the sleeve. Match the seams and pin the 3 raw edges together. Stitch the 3 layers together using a 1cm seam allowance. Zig zag or over lock, press. Repeat on the remaining side.

  1. Nearly finished :-)

  2. Using a zigzag stitch or an over locker, neaten the hem. Using a tape measure, fold under for 2cm the raw edge under the band on both sides. Pin. Press. Fold the hem up for 1cm pin and press. Start stitching just under the band on the RS towards the hem, leave the needle in the fabric and lift up the foot, swivel your work, continue to stitch the hem until the end, leave the needle in your work, swivel, and stitch up the front until you meet the band. Trim and loose thread, press and CELEBRATE.

  1. CONGRATULATIONS your have just made an awesome Nancy Kimono.

#freetutorialandpatternforakimono

251 views

6 Burton Villas,

Hove, Sussex

BN3 6FN

 

See on a map

Contact Sarah

 Tel: 07581028706

sarah@sewretro.co.uk

  • Sew Retro on Facebook
  • Sew Retro on Instagram
  • Sew Retro on Twitter
  • ew Retro on Pinterest

© 2017 by Sew Retro